Toàn quốc: How To Emboss Leather

Thảo luận trong 'THỜI TRANG, GIẦY DÉP, PHỤ KIỆN' bởi ciceroleather, 8/9/2019.

  1. ciceroleather

    ciceroleather Thành viên tập sự

    Tham gia:
    10/3/2019
    Bài viết:
    5
    Đã được thích:
    0
    Điểm thành tích:
    1
    How to emboss leather requires stamps or special embossing tools sturdy enough to leave an impression in the leather. Wet vegetable-tanned leather is required for embossing. Leather working uses special tools to impress designs onto a leather surface. You can create a relief design by either stamping into unfinished leather

    An embossed design on a leather craft like the name of the person receiving, or perhaps flowers or geometrical designs, gives it a permanent personal touch.

    Contents

    Things You’ll Need
    • Damp sponge
    • Solid work surface
    • Leather-embossing stamps
    • Wood mallet
    [​IMG]
    10% OFF ALL WALLETS
    How to emboss leather
    It’s easiest to emboss unfinished leather, but it’s also possible to emboss finished, or stained, leather with some practice. To emboss leather you’ll need a few tools. Start with a sturdy work surface, two to four C-clamps, metal embossing stamps with the shape, pattern, or letters you wish to emboss, a cylinder to hold the stamps, a wooden mallet, and, of course, a piece of unfinished or finished leather.

    Step 1
    [​IMG]
    Place your piece of unfinished leather on a flat worktable
    Place your piece of unfinished leather on a flat worktable. Make sure the front of the leather is facing up.

    Step 2
    Begin the embossing process by using a damp sponge to moisten the leather, which will soften it, making it easier to manipulate. Wipe over the entire surface of the area where you’ll be working, but be careful not to soak it, as the more water the leather absorbs, the longer it takes to dry.

    [​IMG]
    Begin the embossing process by using a damp sponge to moisten the leather
    Wipe your leather surface with a slightly damp sponge. If the water changes the color of the leather, wait for it to dry a little. Wet the top of the leather with the sponge until it is thoroughly wet; the leather appears darker when wet. Wet the back side as well if the leather is thick. Allow it to dry for 10 to 15 minutes or until the leather lightens slightly.

    Step 3
    Affix the leather to a sturdy surface. Use clamps to fasten it down so it does not move during the embossing process. The front side should be facing up. It must be near the edge of a table on which you can hook a strong C-clamp.

    [​IMG]
    affix your first stamp to the cylinder tool
    Next, affix your first stamp to the cylinder tool, and arrange it stamp side down on the surface of the leather, Hold it firmly with one hand. With a sturdy grip, use the mallet to pound the other end of the cylinder, pressing the stamp into the leather.

    [​IMG]
    use the mallet to pound the other end of the cylinder
    Practice makes perfect in this process, to fine tune how much pressure and how many times you need to hit the cylinder to get the desired embossing depth from the stamp.

    Repeat these steps with other stamps if you want to make a more intricate design. Use a leather-finishing product when you have completed you embossing.

    Step 4
    Pour a small amount of leather finish onto a damp cloth, then rub it over your work in circular motions. Ensure the finish gets into all the details of the leather designs to completely protect the leather.

    Related Article: How To Engrave Leather

    Tips & Warnings
    • Leather at least 2 millimeters thick reveals better results than thinner leathers; the farther the stamp or tool can be pressed into the leather, the deeper the impression.
    • If working with thin leather, place several sheets of felt beneath it to help create a clear embossed impression.
    • Practice your techniques on scrap leather of the same type and thickness as your project pieces; this allows you to get a feel for the ideal amount of pressure required to create a clean impression with each stamp or die.
    • If creating a design that requires lining the stamps up one after another, such as spelling out a name, apply a piece of painter’s tape to the leather to act as a bottom-edge guide for each stamp.
    References: https://ciceroleather.com/how-to-emboss-leather/
     

    Xem thêm các chủ đề tạo bởi ciceroleather

Chia sẻ trang này